Volume 4, Issue 1, June 2020, Page: 1-15
Development of Hybridized Completions for Extended Reach Horizontal Wells
Bisweswar Ghosh, Petroleum Engineering Department, Khalifa University of Science & Technology, Abu Dhabi, United Arab Emirates
Omar Jamal Chammout, Petroleum Engineering Department, Khalifa University of Science & Technology, Abu Dhabi, United Arab Emirates
Mohamad Yousef Alklih, Petroleum Engineering Department, Khalifa University of Science & Technology, Abu Dhabi, United Arab Emirates
Samuel Osisanya, Petroleum Engineering Department, Khalifa University of Science & Technology, Abu Dhabi, United Arab Emirates
Received: Dec. 26, 2019;       Accepted: Jan. 9, 2020;       Published: Feb. 10, 2020
DOI: 10.11648/j.pse.20200401.11      View  275      Downloads  49
Abstract
Non-uniform production and injection profiles in extended reach horizontal wells invite several production and recovery issues. Downhole flow control devices, along with dynamic reservoir modeling, have been beneficial in regulating flow, improving productivity from the toe section, delaying water breakthrough, reducing water coning, and improving overall reservoir sweep. However, such measures add to substantial completion costs and may not be economical for marginal reservoirs. Using simple slotted liners is a cheaper option but may not be effective in regulating injection/production profiles in the longer term. This research focused on applying “coupled static and dynamic modeling” to examine and compare five different types of completion designs, using data from a heterogeneous carbonate reservoir. Results show that inflow control device (ICD) integrated completions can achieve better recovery than the slotted, pre-perforated, or engineered liners. Engineered-slotted liners perform better than the pre-perforated-slotted liners. The pre-perforated-slotted liners do not show much improvement over open-hole completions. Finally, a hybrid completion design is optimized by combining ICD with engineered-slotted liners, which showed higher well productivity, lower water cut production, and reduced completion cost.
Keywords
Horizontal Well Completion, Inflow Control Devices, Limited Entry Liners, Production Optimization, Water Control
To cite this article
Bisweswar Ghosh, Omar Jamal Chammout, Mohamad Yousef Alklih, Samuel Osisanya, Development of Hybridized Completions for Extended Reach Horizontal Wells, Petroleum Science and Engineering. Vol. 4, No. 1, 2020, pp. 1-15. doi: 10.11648/j.pse.20200401.11
Copyright
Copyright © 2020 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
Allen, F., Tooms, P., Conran, G. and Lesso, B. “Extended reach drilling: Breaking the 10-km barrier.” Oilfield Review. Winter 1997. Pp 32-47.
[2]
Satter, A. and Iqbal, G. M. (2016). “Reservoir Engineering: The Fundamentals, Simulation, and Management of Conventional and Unconventional Recoveries”. ISBN-978-0-12-800219-3.
[3]
Verma, C. et al. (2017). Drilling Optimization of Extended Reach Multilateral Wells to Maximize Reservoir Contact in Carbonate. SPE-186982. Presented at the Asia Pacific Oil & Gas Conference and Exhibition, Jakarta, Indonesia Oct 2017.
[4]
Yang, M. Li, H., Wang, Y. and Jiang, R. (2019). “Numerical Modelling for the Optimum Design of Horizontal Well. Completions with PSCs in Water Drive Reservoirs.” Arabian Journal for Science and Engineering. Vol- 44. Pp. 5215–32.
[5]
Chammout O. J., Ghosh, B and Alkhi M. Y. (2017). “Downhole flow controllers in mitigating challenges of long reach horizontal wells: A practical outlook with case studies”. Journal of Petroleum and Gas Engineering. Vol. 8 (9), pp. 90-103.
[6]
Jha, P., Smith, C. and Metcalfe R. W. (2016). “Insight Into the Heel–Toe Effect of a Long Horizontal Wellbore Based on a Hybrid Numerical Method”. Journal of Energy Resources Technology. Vol. 138 (1): Pp 12905-13.
[7]
Minulina, P., Al-Sharif, S., Zeito, G. A. and Bouchard, M. J. (2012). “The Design, Implementation and Use of Inflow Control Devices for Improving the Production Performance of Horizontal Wells”. SPE-157453. Presented at SPE International Production and Operations Conference and Exhibition, Doha, Qatar. May 2012.
[8]
Daneshy, A., Guo, B., Krasnov, V. and Ziminet, S. (2010). “ICD Design: Revisiting Objectives and Techniques. SPE-133234. Presented at the SPE Asia Pacific Oil and Gas Conference and Exhibition, Brisbane, Australia, Oct 2010.
[9]
Garcia, L., Coronado, M. P., Russell, R. D., Garcia, G. A. and Peterson, E. R. (2009). “The First Passive Inflow Control Device That Maximizes Productivity during Every Phase of a Well’s Life”. IPTC-13863. Presented at International Petroleum Technology Conference, Doha, Qatar, Dec 2009.
[10]
. Ouyang, L. (2009). “Practical Consideration of an Inflow-Control Device Application for Reducing Water Production”. SPE-124154. “Presented at SPE Annual Technical Conference and Exhibition, New Orleans, Louisiana, USA. Oct 2009.
[11]
Aadnoy, B. and Hareland, G. (2009). “Analysis of Inflow Control Devices”. SPE-122824. Presented at Offshore Europe, Aberdeen, United Kingdom, Sept 2009.
[12]
Gao, C., Rajeswaran, R. T. and Nakagawa, E. Y. (2007). “A literature review on smart well Technology”. SPE-106011. Presented at SPE Production and Operations Symposium, Oklahoma, USA, March- April 2007.
[13]
Burtsev, A., Ascanio, F. A., Mollinger, A. M., Kuvshinov, B. and De Rouffignac, E. P. (2006). “Limited Entry Perforations in HVO Recovery: Injection and Production in Horizontal Wells”. SPE-102656. Presented at SPE Russian Oil and Gas Technical Conference and Exhibition, Moscow, Russia, 3-6 Oct 2006.
[14]
Chow, H., Blount, C. G. and Hilleary, N. (2009). “Annular Isolation of Horizontal Slotted Liners with Chemical External-Casing Packers”. SPE-121643. Presented at SPE/ICoTA Coiled Tubing & Well Intervention Conference and Exhibition, Woodlands, Texas, March- April 2009.
[15]
Wang, J., Dale, B. A., Ellison, T. K., Benish, T. G. and Grubert, M. (2008). “Coupled Well and Reservoir Simulation Models to Optimize Completion Design and Operations for Subsurface Control”. SPE-113635. Presented at Europec/EAGE Conference and Exhibition, Rome, Italy. June 2008.
[16]
Thornton, K., Soliman, M. Y. and Jorquera, R. A. (2010). “Optimization of Inflow Control Device Placement and Mechanical Conformance Decisions Using a New Coupled Well-Intervention Simulator”. SPE-139435. Presented at SPE Latin American and Caribbean Petroleum Engineering Conference, Lima, Peru. Dec 2010.
[17]
Carvajal, G. A., Saldierna, N., Querales, M., Thornton, K. and Loaiza, J. (2013). “Coupling Reservoir and Well Completion Simulators for Intelligent Multi-Lateral Wells: Part-1”. SPE-164815. Presented at EAGE Annual Conference & Exhibition incorporating SPE Europec, London, UK, June 2013.
[18]
Grubert, M. A. et al. (2009). “Coupled Completion and Reservoir Simulation Technology for Well Performance Optimization”. SPE-12552. Presented at SPE Annual Technical Conference and Exhibition, New Orleans, USA. Oct 2009.
Browse journals by subject